Zebra-technologies MtP400 Manual do Utilizador

MtP400 Series Operator’s Manual Printek, Inc. 1517 Townline Road Benton Harbor, MI 49022 269-925-3200 www.printek.com Printek Par

Getting Started Installing Media Each printer comes supplied with either a roll of receipt paper or a cassette of receipt paper depending on the model

Getting Started Movable SupportFigure 3 - Media Support Refer to Figure 4 and unroll enough paper to allow it to lay through the print head as shown

Getting Started Insert the cassette into the printer as shown in Figure 5. Make sure that the smooth side of the cassette with the Printek logo down

Getting Started Host Interface Set Up Prior to using your printer with a computer application, check the interface settings to be sure they match thos

Getting Started Belt Loop System The belt loop system consists of two parts – a knob located on the bottom of the printer and a belt loop strap with a

Daily Operation Introduction For normal daily use, most users will only need to turn the printer on and off, load paper, and recharge the battery a

Daily Operation Enter Button – Used in printer configuration menus to advance to the next setup feature. May also be used to print the settings an

Daily Operation Figure 7 - Tearing Off Printed Output MtP400 SL Models The MtP400 SL models use cassettes of cut sheet receipt paper. In most cases,

Daily Operation Power Connector Battery Indicator Figure 8 - MtP400 Power Connector & Battery Indicator When the power supply is connected, the pr

Daily Operation If the card is read successfully, a short beep will sound, “Card Read Ok” will be displayed and the MCR Indicator will stop flashing

FCC Part 15 Class B This device complies with Part 15 of the RCC Rules. Operation is subject to the following two conditions: (1) this device may no

Printer Configuration Introduction To Setup The MtP400 series printers feature an easy to use control panel “Setup” menu system for setting permanent

Printer Configuration Entering Setup To enter Setup, press and hold the Enter Button while turning on the printer with the Power Button. Continue

Printer Configuration Setup Menu Summary Format Menu Interface Menu Format n Serial IrDA Bluetooth Wi-Fi Options MenuFormat Name Up to 16 Character

Printer Configuration The bottom line of the display shows the Format that is currently selected. If you wish to change to a different format, press

Printer Configuration Spacing Spacing 3 Lines Possible Values: 0 … 3* … 10 Lines When printing text, this feature sets spacing between lines. The he

Printer Configuration Print Contrast Print Contrast 0 Possible Values: -75 … 0* … +125 in increments of 5 The printer automatically adjusts the amoun

Printer Configuration Mark Sensitivity Mark Sensitivity 0 Possible Values: -10 …0* …+10 This feature allows the Black Mark/Paper Fault sensor to be a

Printer Configuration Serial Interface INTERFACE MENU Serial Note that “Serial” must be displayed on the bottom line of the display in order to acce

Printer Configuration Parity Parity None Possible Values: None*, Even, Odd This feature sets the parity checking requirements for the data bits in th

Read all setup and operating instructions before proceeding with operation. Do not operate in an enclosure unless properly ventilated. Make sure n

Printer Configuration IrDA Interface INTERFACE MENU IrDA Note that “IrDA” must be displayed on the bottom line of the display in order to access the

Printer Configuration Pairing Mode Pairing Mode Paired Possible Values: Paired*, Unpaired This feature allows Bluetooth pairing to occur between the

Printer Configuration Address Address 0080371B8F32 Possible Values: Twelve digit hexadecimal string. This feature displays the unique hardware value

Printer Configuration WLAN Channel WLAN Channel 1 Possible Values: 1* … 14 Note that this feature is only available if the WLAN Type is set to Peer-t

Printer Configuration WLAN Auth WLAN Auth Auto Possible Values: Auto*, Open, Shared This feature specifies the authentication method that will be use

Printer Configuration Tunnel Port Number Tunnel Port# 08023 Possible Values: 00000 … 08023* … 65384 This feature specifies the TCP/IP port to be used

Printer Configuration Auto Power Down Auto Power Down Off Possible Values: Off*, 1 Minute Delay … 15 Minute Delay This feature sets whether the print

Interfacing To A Host Computer Every MtP400 is equipped with an RS-232C Serial Interface. Optional factory installed interfaces are also available f

Interfacing to a Host Computer IrDA Interface In addition to the standard Serial interface, your MtP400 may be equipped with an optional IrDA interfac

Interfacing to a Host Computer When discovered, the default name that will appear will be “MtP400-xxxx” where “xxxx” is the last four digits of the Bl

Power Considerations MtP400 printers are designed to provide superior output using as little power as necessary. This provides the longest possible

Maintenance and Troubleshooting Cleaning In normal environments, the printer should be cleaned after printing a few rolls of paper or if there are vo

Maintenance and Troubleshooting Battery Care Charging the Battery The printer’s battery is charged in the printer using an optional power supply. Pow

Maintenance and Troubleshooting Testing the Power Supply and Battery To verify that the printer’s internal battery charger is functioning properly, pe

Maintenance and Troubleshooting Troubleshooting When encountering problems, the cause may be the printer or may sometimes be due to other problems wit

Maintenance and Troubleshooting Other Problems Problem Possible Cause Solution Battery not installed properly. Remove and reinstall battery making su

Maintenance and Troubleshooting Obtaining Service If service is required for your printer, please contact the company where you purchased your printe

Advanced Setup Features An additional security menu is available for system administrators who prefer to “lock out” operator changes to the various

TABLE OF CONTENTS Introduction ...

Print & Font Samples Print Samples 45

Print & Font Samples Courier Font With International Extended Character Set Courier Font PC Line Drawing Extended Character Set 46

Print & Font Samples Sans Serif Font 47

Specifications Printer Specifications Printing Specifications Printing Method: Direct Thermal, Up To 3.3 Inches Per Second Printing Resolution:

Specifications Physical Specifications Size: MtP400 & MtP400 LP – 8.1 x 6.6 x 3.1 inches, 19.56 x 16.76 x 7.87 cm (LxWxH) MtP400 SL – 9.6 x 6.6

Specifications Media Specifications Receipt Paper General Specifications: 0.0022 to 0.0065” (0.056 to 0.089mm) Thick Black Mark Sensing On Printed

Specifications Black Mark Position The vertical position of a Black Mark is dependent on the application program that will be used to search for and p

Specifications Supplies and Accessories Supplies Battery: 7.4V, 2200 mAH Li-Ion Available separately or in 5 or 20 packs. Receipt Paper – Rolls:

Table of Contents Maintenance and Troubleshooting...

Glossary of Terms 802.11 Wireless networking communication standards created by IEEE. access point An interface between a wireless network and a wi

Glossary IP Internet Protocol. A specification for packets, or datagrams, of data and an addressing method to allow the exchange of data with anothe

Introduction Thank you for purchasing a Printek MtP400 Series Mobile Thermal Printer. The MtP400 series offer a variety of configurations to suit a

Getting Started Battery Installation and Charging Note: You must charge the battery for at least 2½ hours prior to the first use. The battery for yo