Zebra-technologies SL5000r/T5000r Manual do Utilizador

Printer Protocol Interpreter (PPI) ZGL™Programmer’s Reference Manual for ZGL,a Zebra® ZPL® Printer Protocol InterpreterThermal Series Printers

10Chapter 1 PPI/ZGL SETUP MenuPPI/ZGL SETUP MenuEnable* Disable560K Bytes* 160-3600K BytesPPI/ZGL SETUP 1ZPL Compatible126*Command PrefixLabel Prefix

PPI/ZGL SETUP Submenus 11PPI/ZGL SETUP SubmenusZPL CompatibleThis menu allows you to select the compatibility to ZPL-I or ZPL-II.• ZPL-I = Zebra Progr

12Chapter 1 PPI/ZGL SETUP MenuCommand PrefixThis item allows you to select the prefix for the control instructions command.The range is 1-255, and th

PPI/ZGL SETUP Submenus 13MC Label FmtThe ^MC command determines whether the printed label image should be retained for use in the immediately followin

14Chapter 1 PPI/ZGL SETUP MenuLeft PositionThe ^LS command specifies a horizontal offset to be added to all label element positions. The Left Positio

PPI/ZGL SETUP Submenus 15IS Label FormatThe ^IS command saves the printed label image by name for later recall as part of a label definition. The IS L

16Chapter 1 PPI/ZGL SETUP MenuCharacter Group And Character SetsThis menu item selects the character set used by the printer. The available character

172 Fully Supported Commands^Bx - BarcodesThis command selects various barcodes. PPI supports the following ZPL barcodes:^B1 Code 11^B2 Interleaved 2

18Chapter 2When barcodes are generated on printers with unique print densities, the dot ratio of the wide/narrow bar/space does not match the ZPL pri

19~EF / ^EF - Erase FormatThis command deletes all label formats stored with the ^DF Download Format command.~EG / ^EG - Erase Downloaded ImagesThis

20Chapter 2^FT - Field Type SetThis command sets the x/y coordinate (relative to the “home” position) of a subsequent field. It differs from the ^FO

21^HY - Upload GraphicThis command uploads different graphic image formats from RAM or Flash to the host.^IL - Image LoadThis command recalls an enti

22Chapter 2^LL - Label LengthThis command defines the length of a label in printer dots. Any label printed on continuous media causes the defined len

23~NT - Set Currently Connected Printer TransparentThis command sets the currently connected network printer to transparent.^PM - Print Mirror Image

24Chapter 2^XF - Recall FormatThis command recalls a label definition previously stored with the ^DF Download Format command and merges ^FN dynamic f

253 Command Enhancements And Differences^A@ - Select Font by NameThis command only applies to built-in fonts or bitmap fonts downloaded via the ~DB c

26Chapter 3^B$B - UPCSHIPCommand Format: ^B$B fp, hgt, rdt, posb: UPCSHIP barcode commandfp: Barcode orientationN = No Rotation (Default)R = Rotate 9

27^B$D - FIMCommand Format: ^B$D fp, type, heightd: FIM barcode commandfp: Barcode orientationN = No Rotation (Default)R = Rotate 90 degrees, clockwi

28Chapter 3Standard Sets (cont.) German 006France 1 007France 2 008Italy 009Spain 010Miscellaneous 011Japan 012IBM CP 850 013Arabic Sets ASMO 449 100

29European SetsLatin 2 8859-2 300Code Page 852 301Mazovia 302Kamenicky 303Roman 8 304PC-437 Slavic 305Slavic 1250 306Code Page 865 307Code Page 860 3

Printer Protocol Interpreter (PPI) ZGLProgrammer’s Reference Manual for ZGL,a Zebra ZPL Printer Protocol InterpreterThermal Series Printers

30Chapter 3^CW - Font IdentifierPPI uses scalable fonts rather than bitmapped fonts. The device naming convention differs as follows:ZPL device speci

31~DG - Download GraphicsThe device naming convention differs as follows:ZPL device specifiers:R: DRAMB: Optional MemoryE: Extra EPROMZ: Standard EPR

32Chapter 3^HR - Calibrate RFID Transponder PositionThis command initiates an RFID transponder calibration for a specific RFID label and returns the

33^JE - Disable DiagnosticsThis command disables Hex Dump mode.~JP - Pause & CancelThe PPI ONLINE light is illuminated when the printer is online

34Chapter 3When LP+ Text Mode is set to “Auto Pass-thru,” non-PPI data is automatically detected and passed through to the LP+ emulation (PPI data is

35~PP / ^PP - Programmable PauseThe ~PP command takes the printer offline as soon as the current label being printed is completed. The exact moment a

36Chapter 3^RZ - Set RFID Tag PasswordThis command lets you define the password for the tag during writing.~SD - Set DarknessIdentical darkness value

37A ZGL Menu ConversionsWhen substituting a Zebra Xi III model printer with a SL5000r/T5000r printer, refer to the ZGL conversion table below.Table 2:

38Appendix A Zebra Xilll Series SL5000r/T5000r with ZGL EmulationPrint Width - Width of image to be printed in Inches, MM or Dots.Printer width depend

39 Zebra Xilll Series SL5000r/T5000r with ZGL EmulationMedia Power Up - Media action when the printer is powered up.Feed* - Feeds a label to1st web.Ca

Trademark AcknowledgmentsZPL, ZPL II, and Zebra are registered trademarks of Zebra Technologies Corporation.PPI is a trademark of Printronix, Inc.Prin

40Appendix A Zebra Xilll Series SL5000r/T5000r with ZGL EmulationHead Resistor - Must be updated when printhead changed.NOTE: Head Resistance detected

41 Zebra Xilll Series SL5000r/T5000r with ZGL EmulationSave Settings -Permanent* - Saves changes even after power is turned off.Temporary - Saves unti

42Appendix A Zebra Xilll Series SL5000r/T5000r with ZGL EmulationSubnet Mask (opt) -Dynamic - User may set, but server can assign.Permanent* - User mu

43B ZGL-DBCSOverviewThis appendix describes the additional and unique commands for • T5000 ThermaLine ZGL-DBCS SeriesThe T5000 ThermaLine ZGL-DBCS in

44Appendix B ZGL-DBCS SeriesZGL-DBCS SeriesThe ZGL-DBCS series include ZGL-Hangul, ZGL-HanziGB, and ZGL-JAP emulation software.High Byte MenuThe menu

Command Syntax 45OritFont orientation:N - No rotation (Default)R - Rotate 90 degrees clockwiseI - InvertedB - Rotate 270 degrees clockwiseFor Scalable

46Appendix B ZGL-DBCS Series(C) Font Identifier CommandPurpose This command assigns a one-character identifier to a built-in or downloaded font.Synta

47C Contact InformationPrintronix Customer Support CenterIMPORTANTPlease have the following information available prior to calling the Printronix Cus

48Appendix C Corporate OfficesCorporate OfficesPrintronix, Inc.14600 Myford RoadP.O. Box 19559Irvine, CA 92623-9559Phone: (714) 368-2300Fax: (714) 36

1 Introduction ... 9About This Manual...

174779-001G*174779-001*

Table of Contents~DU - Download Unbounded TrueType Font ... 18~EF / ^EF - Erase Format...

Table of Contents~NR - Set All Network Printers Transparent ... 22~NT - Set Currently Connected Printer Transparent ...

Table of Contents^MC - Mp Clear...... 34^MD - Media Darkness ...

91 IntroductionAbout This ManualThis manual explains the differences between the Printer Protocol Interpreter Zebra Graphic Language (ZGL) Utility an